Ffmpeg build rpi how to#
Ffmpeg build rpi code#
Ffmpeg build rpi Pc#

# 1 - Demo PC sends a video # 2 - Docker container with ffmpeg transcodes it and sends it back # STEP 1 - Demo pc (eth0: 10.143.0.245): # start sending the video file at udp port 9999.įfmpeg -re -i big_buck_bunny.mp4 -vcodec mpeg4 -an -b 1024k -s 640x480 -f mpegts udp://10.143.0.246:9999 ?pkt_size=1316 Ensure you have a stable power supply and good network connection.

This has only been tested for Raspberry Pi, other ARM SBCs have not been tested yet.

Ffmpeg build rpi how to#

Sudo ovs-docker add-port ovs-br1 eth0 ffmpeg_nonet_privileged -ipaddress=192.168.0.2/24 -gateway=192.168.0.1ĭocker exec ffmpeg_nonet_privileged ifconfig # this should print out 'lo' and 'eth0' # test (RPi: 10.143.0.246, Demo pc: 10.143.0.245) # big_buck_bunny.mp4 is not provided within the docker image # if it is available on the docker host (RPi), use `docker cp.` to copy it inside the imageįfmpeg -re -i big_buck_bunny.mp4 -vcodec mpeg4 -an -b 1024k -s 640x480 -f mpegts udp:10.143.0.245:9999 ?pkt_size=1316įfplay udp://10.143.0.246:9999 # for the Demo pc # commands you might need later. Hey, welcome to the FFmpeg tutorial This page has instructions on how to compile and install FFmpeg with the OpenMAX driver, which allows you to use the Raspberry Pi GPU for H.264 encoding. Sudo iptables -A FORWARD -i $priintf -o $pubintf -m state -state RELATED,ESTABLISHED -j ACCEPTĭocker run -net=none -name=ffmpeg_nonet_privileged -privileged -itd tgogos/ffmpeg:latestĭocker exec ffmpeg_nonet_privileged ifconfig # this should print out only 'lo' # add a NIc Sudo iptables -A FORWARD -i $priintf -j ACCEPT Sudo iptables -t nat -A POSTROUTING -o $pubintf -j MASQUERADE * Beware that this compilation procedure takes a few hours to finish

Video file: Big Buck Bunny by Blender Foundation.

Docker image to start with (FROM): resin/rpi-raspbian:jessie-20160831.

Host OS: Raspbian Jessie Lite image (downloaded -raspbian-jessie-lite.zip from the official site).

Ffmpeg build rpi code#

If you'd like to reproduce the whole process take a look at the section below 'Download ffmpeg source code / compile' Test environment The docker image has been pushed to, you can save time by pulling it and then start testing. configure -arch=armel -target-os=linux -enable-gpl -enable-libx264 -enable-nonfreeįfmpeg -encoders # test it works Install and test ffmpeg on Raspberry Pi 3 (with Docker)ĭocker containers were used, so ffmpeg was not installed directly on the RPi. configure -host=arm-unknown-linux-gnueabi -enable-static -disable-opencl Sudo apt-get install build-essential libmp3lame-dev libvorbis-dev libtheora-dev libspeex-dev yasm pkg-config libfaac-dev libopenjpeg-dev libx264-dev Sudo apt-get install deb-multimedia-keyring Sudo sh -c 'echo 'deb-src jessie main non-free' > /etc/apt//deb-multimedia.list ' Sudo sh -c 'echo 'deb jessie main non-free' > /etc/apt//deb-multimedia.list '